Joey Gill /
04.10.2014 03:10 PM
Roland’s VC-1SC and VC-1 DL Modules

Roland’s VC-1SC and VC-1DL converter/transcoder/processor modules

For as long as I’ve been in the broadcast engineering business, there have been small “brick” pieces of gear. Some of these were merely pin-out test devices, some were isolators, and some even functioned as test/sync generators. Until recently though, these were just about the only items that you could fit in your coat pocket, feature wise.

Fast-forward to the present time where manufacturers such as Roland Systems Group have been packing more and more features into smaller packages. Prime examples of these new technologies include that company’s VC-1-SC up/down/cross scan converter and their VC-1-DL bidirectional converter that’s equipped with delay and frame sync.

It’s rare that I review two products in one article; however, the simplicity and straightforward design on these little boxes makes sense in this case.

FEATURES

Both units are housed in similar small aluminum cases and are powered via a PSB 1U 9-Volt adaptor. The chassis has a slick power cord retaining clip to keep the plug secure, and although the adaptors are rated at 18 Watts, I found no power consumption figures. (The power adaptors and converters do run cool to the touch.) While the two units share many connectivity traits such as USB, DIP switches, ref in, power connector and status LEDs, there are differences in connector types, ie: HDMI, RCA, BNC, and VGA. The VC-1 products feature onboard re- clocking and support for both level A and B 3G SDI. The units are very well labeled in terms of hookup, block diagrams and DIP switch programming.

The VC-1-SC provides up-, down-, cross-, frame-rate, I/P and aspect ratio conversion. In addition, it offers 3G I/O, HDMI I/O, RGB/component inputs, composite video input, and support for HDCP. The VC-1-SC also includes a built-in frame synchronizer, scaler, audio embed-der and de-embedder. The VC-1 RCS PC/ MAC application provides control.

The VC-1-DL is a bidirectional SDI/ HDMI converter, with delay and frame sync functionalities. It features lossless image conversion, 3G capabilities, HDCP support, separate audio and video delays of up to nine fields, audio embedding/ de-embedding and channel selection. The VC-1-DL also uses Roland’s VC-1 RCS PC/ MAC control application.

IN USE

I was shipped a VC-1-DL and VC-1-SC for evaluation. I tried out the VC-1-SC converter first, as it seems I’m always drawn to transcoders! I connected the power supply, and hooked up the HD/SD SDI output to a Blackmagic Design eight- inch dual monitor. For an input source I attached my six-year-old Gateway laptop computer to the converter via a VGA con- nection.

At this point, I guess I expected a picture to just appear; however, I wasn’t so lucky. My first reaction was to start pressing the “input” select switch. While I could see the monitor screen flash a bit, there was still no picture. Next I made sure that the “second screen” feature was activated on my computer and I was pretty sure that I had that one right. Next, I changed the resolution on the PC away from 1280 x 768 to 1024 x 768. Viola! I had a very At this point, I guess I expected a picture to just appear; however, I wasn’t so lucky. My first reaction was to start pressing the “input” select switch. While I could see the monitor screen flash a bit, there was still no picture. Next I made sure that the “second screen” feature was activated on my computer and I was pretty sure that I had that one right. Next, I changed the resolution on the PC away from 1280 x 768 to 1024 x 768. Viola! I had a very

Next, it was time to try the USB connectivity and control via my PC. I downloaded the VC-1 RCS software and installed the application. The process proved to be simple and straightforward. After installing this app, I connected the USB cable between my PC and the VC-1-SC, and when I clicked on the desktop icon, the application launched and I had a full screen of options for the VC-1 SC all at the control of my mouse. These included DIP switch settings, inputs, scaling, analog input parameters such as phase, col- or gain, as well as brightness and contrast. Also displayed were audio level and level alarm adjustments, HDCP, H/V positioning and more.

To test the VC-1-DL, I ran a 1080i direct feed from my NBC program stream to the input of one of the dual eight-inch monitors. I fed the looped output of that monitor to the input of the VC-1-DL and connected the output of the VC-1-DL to the other monitor in the dual configuration.

When I connected the power adaptor I was able to see the NBC incoming feed on both monitors without any discern- able delay between them. As a test of audio monitoring/de-embedding capabilities, I took the audio out from the VC-1-DL via the RCA connectors and connected the feed to an American Audio rackmount LED meter set that we use. I immediately saw audio registering on the meter. By using the RCS software, I was able to connect to the VC-1- DL and dial in varying amounts of video or audio delay—up to 4.5 frames, in 0.5 frame increments. (For fine delay, you can also select lines of delay as well.) And while this can be accomplished with on-chassis controls, I wanted to try out the GUI which I found to work very nicely.

After dialing in some video delay, I could easily detect that delay between my two video monitors. Connecting a set of headphones (in place of the metering) allowed me to confirm that I was indeed affecting the lip sync. When I dialed the same delay into the audio delay adjustment, the lip sync stayed “dead on.” Other adjustments on the GUI included audio embedding options such as channels and groups, input embedding selection, audio level controls, metering thresholds (for establing LED alert levels), DC warning thresholds and HDCP (High-bandwidth Digital Content Protection) encryption and mask.

SUMMARY

I left both of the units up and operational for about a month. Occasionally, I’d disconnect them and reconnect. Never once did I have to restart them or perform any sort of reset operations.

I spoke with tech support at Roland about the 1280 x 768 resolution issue and they advised me that no one else had re- ported this, but they would check into it. They got back to me later that they were indeed able to confirm the problem in their lab and would be addressing it in a software update. (I may have been the only user who tried using a 1280 x 768 resolution setting.) I did check about a dozen other resolutions and they all worked perfectly.

In summation, I found the Roland “bricks” to be well worth the money. Video quality was more than acceptable, they were easy to operate and they proved to be very reliable.

Joey Gill is chief engineer at WPSD-TV in Paducah, Ky. and has been with the station for 30 years. He has worked in television since 1977. He may be contacted at respond2jgill@yahoo.com.

FAST FACTS

APPLICATION
Video format transcoding, audio embedding/de-embedding and general processing

KEY FEATURES
Cost effectiveness, compact size, low power consumption and ease of operation

PRICE
VC-1-SC, $995 MSRP; VC-1-DL, $795 MSRP

CONTACT
Roland Systems Group
323-215-2111
www.rolandsystemsgroup.com



Comments
Post New Comment
If you are already a member, or would like to receive email alerts as new comments are
made, please login or register.

Enter the code shown above:

(Note: If you cannot read the numbers in the above
image, reload the page to generate a new one.)

No Comments Found




Thursday 10:05 AM
NAB Requests Expedited Review of Spectrum Auction Lawsuit
“Broadcasters assigned to new channels following the auction could be forced to accept reductions in their coverage area and population served, with no practical remedy.” ~NAB

Manor Marketing /   Tuesday 08:24 AM
aQ Broadcast Introduces New aVS Version 4 Firmware
Manor Marketing /   Tuesday 08:32 AM
aQ Broadcast Features aQ Production Suite at IBC 2014
Sue Sillitoe, White Noise PR /   Tuesday 11:50 AM
Prism Sound Releases SADiE Version 6.1

 
Featured Articles
News Technology
News Technology
Discover TV Technology