Jay Holben / Lighting Technology
08.15.2014 11:40 AM
The Parabolic Aluminum Reflector

Jay Holben
The next in line on our examination of lighting fixtures is the PAR, which is an acronym for Parabolic Aluminum Reflector.

The classic PAR is a reflector and lamp all in one. It is a sealed-beam lamp, like an old-school car headlight. The rear of the envelope (the glass enclosure of the bulb) has a parabolic shape and is coated in an aluminum material for a built-in reflector.

The filament of the lamp is placed in the precise focal point of the parabolic reflector so that the light rays exiting the lens are parallel. This creates a focused beam of illumination from a compact, lightweight lamp.

Fig. 1: PAR Diagram
Fig. 2: PAR Lenses
The PAR has four major components: lens (A); reflector (B); base (C); and filament (D). (Fig. 1.)

As the PAR has a fixed relationship of reflector, lamp and lens, the only way to change the spread of the light is to change the bulb (or, in higher-end HMI PARs, change the lens). PARs typically come in very narrow spot, narrow spot, medium flood and wide flood varieties. The quickest way to tell the difference is, the more “stuff” you see on the lens, the wider the spread of the light. (Fig. 2.)

As a standard bulb, a PAR is typically used as a wide, intense floodlight. You’ll see them often used for exterior illumination, particularly security lights. Small PAR fixtures are great for “spotty” and intense practical lighting on a set. You often see PAR lamps in overhead recessed lighting in commercial and private venues.

PARs have a size designation: PAR36, PAR64—which is a reference to the diameter of the lens in 1/8-of-an-inch increments. Take the number, divide it by 8 and that will give you the lens diameter in inches. So a PAR64 has an 8-inch diameter lens (64/8 = 8).

The simplest professional PAR fixture is the PARcan, which takes the PAR globe and encloses it into a simple metal snoot to make it more of a spotlight fixture. The PARcan is used more often in theatrical and concert lighting than it is in film and television. The last time I used PARcans on a shoot it was at the Encounter Restaurant at Los Angeles International Airport (the spaceship looking building in the center of the airport, which most people mistakenly believe is the control tower). I used 112 PARcans on the ground, pointing straight up, circling around the entire structure to light up the outside wall. They’re a workhorse fixture, but the light is often too harsh for direct use on faces.

The next most common usage of PARs is in a multi-lamped fixture. We use PAR64s in 4-lamp, 6-lamp, 9-lamp, 12-lamp and even 24-lamp configurations, all in one fixture. The 6- and 9-lamp configurations are often called “Maxibrutes” and the 24-lamp is called a Dino or Wendy light. These are often used for nighttime exteriors off a condor or cherrypicker for wide, broad backlight. PAR64s are 1,000 W lamps, so 24 of them in a fixture provide a considerable punch.

The individual lamps in the multi-array fixture can be swapped out for very narrow spot (nicknamed “firestarters” for the intense heat they project in a very tight beam), narrow spot, medium flood or wide flood for different uses. It’s possible to have some wide, some medium and some spot in the same fixture to cover greater distances with the spread of light.

The light beam that comes from the PAR is elliptical in shape and, often, can be rotated vertically or horizontally by spinning the physical lamp itself.

HMI Pars have a sealed beam reflector and clear lens and require an additional lens to be placed in the fixture—they are typically spot (near clear), medium (some facets in the lens), wide (more facets) and stipple, or very wide (the most facets in the lens).

The only other real oddball in the PAR world is the ETC Source Four PAR, which features the same lamp as the ETC Source Four Ellipsoidal Reflector Spotlight, precisely positioned in a parabolic reflector and separate, interchangeable, lenses for spot, medium and flood.

Finally, FAY PAR lamps have a dichroic filter to raise the color temperature to 5,000 K from a tungsten lamp.

Jay Holben is the technical editor of Digital Video and a contributor to Government Video. He is also the author of the book “A Shot in the Dark: A Creative DIY Guide to Digital Video Lighting on (Almost) No Budget.”

Post New Comment
If you are already a member, or would like to receive email alerts as new comments are
made, please login or register.

Enter the code shown above:

(Note: If you cannot read the numbers in the above
image, reload the page to generate a new one.)

Posted by: Anonymous
Tue, 08-19-2014 06:38 PM Report Comment
I'd like to add that PAR lights are typically cheap to rent and very efficient for incandescent fixtures. Because of the shape of this lamp, nearly all the light exits the front. Still, they're typically 1,000W a piece, so you've got to have a considerable power source to make a show of it.

Thursday 11:07 AM
The Best Deconstruction of a 4K Shoot You'll Ever Read
With higher resolutions and larger HD screens, wide shots using very wide lenses can be a problem because they allow viewers to see that infinity doesn’t quite resolve into perfect sharpness.

Featured Articles
Discover TV Technology